HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. RF transmitter and RF receiver of Mhz; 3 push buttons; IC HT12D; IC HT12E; Hearders (male or female it doesn’t care); 3 resistors with a value from ( to. HT12D is a decoder integrated circuit that belongs to series of decoders. This series of decoders are mainly used for remote control system applications, like.
Author: | Dourn Julabar |
Country: | Spain |
Language: | English (Spanish) |
Genre: | Music |
Published (Last): | 1 May 2016 |
Pages: | 32 |
PDF File Size: | 2.95 Mb |
ePub File Size: | 2.94 Mb |
ISBN: | 236-5-14586-310-5 |
Downloads: | 16110 |
Price: | Free* [*Free Regsitration Required] |
Uploader: | Faetaur |
Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.
Choosing Battery for Robots. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. If any valid data is received they can be obtained from these four pins. The serial input data is compared with the local addresses three times continuously. It is mainly provided to interface RF and infrared circuits. In simple terms, HT12D converts the serial input into parallel outputs.
Virgin Galactic — Commercial Space Flight. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. They can also be connected to LED to physically view the received data.
So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. This high-density System-in-Package SiP integrates controller, power switches, and support components.
These are the 8-bit address bits, which is used to protect your data. Submitted by admin on 27 October Arduino based GPS receiver. If you want security you can connect any of the 8 pins to 5V iic make it high. It is not mandatory to use it. The input data code is decoded when no error or unmatched codes are found.
How IC HT12D works?
HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Valid transmission; active high. It is very important that your Decoder should have the same address of that of the encoder. Skip to main content.
HT12D Decoder IC
They are paired with 2 12 series of encoders. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc.
The Encoded 12 bit output data obtained from HT12E has to be given here. This pin powers the IC should use only 5V. This oscillator can be used by connecting these two pins through a 1M Resistor.
We should jc the bits in ht1d pattern on Encoder and Decoder IC to pair them. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.
How IC HT12D works? | JAY Robotics’s Blog
A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Connected to the Ground of circuit. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. Interface GPS with Arduino.
What is Web Browser. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.
TL — Programmable Reference Voltage. This pin will go high when a data is received. Supply voltage; 5V 2. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received.
HT12D RF Decoder IC Pinout, Details, Equivalent & Datasheet
In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. A valid transmission in indicated by id high signal at VT pin. The data on 4 bit latch type output pins remain unchanged until new is received. Choosing Motor For Robots. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.
Interface SD Card with Arduino. These two ICs together form an Encoder and Decoder pair.