free pdf instructions. Find the office and computer equipment manual you need at ManualsOnline. Lexmark CN Printer User Manual. Page 1. Page 2. Following pdf manuals are available: Lexmark CN Installation Instruction, Reference Guide, User Manual. Service Manual. xx, 4xx. Go Back. Previous. Next. Assembly 1: Covers . 4. 3. 1. 6. 5. 8. 7. 2. 9 www MK-Electronic de.
|Published (Last):||15 July 2004|
|PDF File Size:||12.24 Mb|
|ePub File Size:||5.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page xx, 4xx Remove the two top screws E near the front. The following instructions show how to remove them. A new gear is included in the spring clamp kit and must be used with the new spring clamp. Unplug and change mode. If a sensor is replaced, enter the digit hexadecimal toner density value TPS value from the bar code next to the sensor. Check the tray adjustments for the size of paper used. Loading paper and specialty media.
First transfer Page – Step 4b: Page xx, d540n Select the printer from the list of printers installed on the computer. Unsupported USB device, please remove. Position the printer with the front cover overlapping the front edge of the table.
If two option trays are used, the step 9. Never replace both of the components without performing a POR after installing each one, or the printer will be rendered inoperable: Remove the LVPS shield.
This problem most commonly occurs when projecting transparencies with reflective overhead projectors. Use of lubricants other than manuwl specified can cause premature failure. Begin here to locate the service error code, user status message, user error message, symptom table, service checks, and diagnostic aids in this manuall to determine the corrective action necessary to repair a malfunctioning printer.
Configuration Id xx, 4xx Configuration ID The two configuration IDs are used to communicate information about certain areas of the printer that cannot be determined using hardware sensors. Rear Shield Removal xx, 4xx Detach the operator panel cable C from the panel.
Print defects guide Page 1 of 1 Match a set of repeating defects on a print job to the marks on one of the vertical lines. Old, damaged or out-of-specification media can and will cause feed and transport problems.
Lexmark C540n Service Manual
Page xx, 4xx Continuing the removal with or without the spring clamp kit Disconnect the x540n springs A, B from the side frames, leaving the right one A attached to the ITU or ITU spring clamp. Light colored line, white line, or incorrectly colored line. Supported paper sizes, types, and weights. Don’t show me this message again.
Lexmark C540n C543dn C544 series service manual download
The default is pages. The charge rolls A put a uniform negative charge over the entire surface of the photoconductor to prepare it for the laser beam. Replacing the waste toner bottle. Remove the waste toner bottle. Pull corner of cable cover B away from the right side to access the sensor posts C. Developer Unit Removal xx, mqnual Installation notes: Print the Quick Test Page on letter or A4 paper.
Lexmark CN manuals |
This must be performed before color skew adjustment is attempted. Theory Of Operation xx, 4xx Theory of operation Print engine theory Electrophotographic process EP process The method that all laser and LED printers use to print is called the electrophotographic process.
Page 48 xx, 4xx Service error messages 1xx, manhal continued Error code Description Action Repeat steps 2 through 7 for any other files. Some slick or coated papers may also cause background problems.
By pressing ‘print’ button you will print only current page. Did this remedy the situation? Repair Information xx, 4xx 4.
Remove the packing in question removed? For more network troubleshooting information, consult the Lexmark Network Setup Guide.
Index xx, 4xx Index Numerics color theory Color Trapping 3x—9x user messages — configuration ID 1xx service mnual — configuration menu 2xx paper jam accessing locations Auto Color Adj messages — available tests sheet media tray Fuse Page – Step 6: Transfer unit clean Once the toner image on the transfer belt has been transferred to the page, the transfer belt rotates around and is cleaned by the cleaning blade G.
Printing menu settings pages. If the bushing is damaged, remove it by pressing the tabs on each side.