This standard is issued under the fixed designation C42/C42M; the number . of core test results.2 and that is free of is the individual responsible for analysis or. ASTM C42/C42M () Standard Test Method for Obtaining and Testing Drilled ASTM International, West Conshohocken. Free SCIRP Newsletters>> . ASTM C Potential Resistance to Degradation. In-situ Tests . Determine time from start until no free water is on ASTM C42, Coring, 3 cores/5, sf.
|Published (Last):||26 December 2014|
|PDF File Size:||8.25 Mb|
|ePub File Size:||17.84 Mb|
|Price:||Free* [*Free Regsitration Required]|
Ends are not to be capped. When grinding or capping of the bearing surfaces is.
ASTM CC42M – 04 – Free Download PDF
The acceptance criteria for core strength is to be established by the specifying authority. If time permits, the concrete should not be removed before it is 14 days old. Measure core diameters to the nearest 0. Cap or grind the cores, and test them within 48 h of receipt.
If necessary, saw the ends of the specimens until the following requirements are met: A specimen taken perpendicular to a vertical surface, or perpendicular to a surface with a batter, shall be taken from near the middle of a unit of deposit when possible and not near formed joints or obvious edges of a unit of deposit.
Do not use specimens with projections or depressions greater than 0. BoxFarmington Hills, MI Average values are given in the table. Cores for Compressive Strength 7.
If this is not practical, removal of concrete can proceed if the cut surfaces do not display erosion of the mortar and the exposed coarse aggregate particles are embedded firmly in the mortar.
The ends shall be sawed or ground to tolerance or capped in accordance with capping procedures for hardened concrete specimens of Practice C Core specimens with length-to-diameter ratios less than 1. Therefore, results of two properly conducted tests on cores sampled from the same hardened concrete where a single test is defined as the average of two observations coreseach made on separate adjacent drilled 4 in.
CObtaining and Testing Drilled Cores and Sawed Beams of Concrete
Combining values c442 the two units may result in nonconformance. ACI provides core strength acceptance criteria for new construction. Last previous edition C 42 — The saw shall have a diamond or silicon-carbide cutting edge and shall be capable of cutting specimens which conform to the prescribed dimensions, without excessive heating or shock. Current edition approved Feb. C 39 with the addition of the following information: The preferred length xstm the capped specimen is between 1.
Additionally, this method may be used to provide strength information on older structures. They are applicable to both dry and wet concrete for strengths between and psi [14 to 42 MPa]. NOTE 3—Correction factors depend on various conditions such ashm moisture condition, strength level, and elastic modulus.
Measure the lengths of such cores in accordance with Test Method C If the ratio of the length to the diameter of the core specimen exceeds 2. This standard has been approved for use by agencies of the Department of Defense.
ASTM C42-C42M – 04
Length of Drilled Cores 6. When capping is employed the caps shall be as asym as practicable and shall be formed of high-strength gypsum plaster. In-place test methods may be used to estimate the level of strength development prior to attempting removal of concrete samples. The relationship is affected by many factors such as the strength level of the concrete, the in-place temperature and moisture history, and the strength gain characteristics of the concrete.
Core diameters less than 3. When the line atsm contact is not straight or contains projections or depressions having heights or depths greater than 0. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
The values stated may not be exact equivalents, therefore each system must be used independently of the other. Parte 1 de 2 Designation: Determine tree average diameter by averaging two measurements taken at right angles to each other about the midheight of the specimen. NOTE 2—Prior to capping, the density of a core may be determined by weighing it and dividing it by the volume calculated from the average diameter and length, or by any other standard method for determining density.
Livro sobre Cimento Portland e Concreto. Thus, these factors should be applied to high-strength concrete with caution. For strengths above psi [70 MPa], test data on cores show that the correction factors may be larger than the values listed above. A superscript epsilon e indicates an editorial change since the last revision or reapproval.
Originally published as C 42 — 21 T. Significance and Use 3. A number in parentheses indicates the year of last reapproval. Sampling and sample preparation requirements are given to ensure that dimensional requirements are met and that the specimens are comprised of intact sound concrete as free of flaws as the particular structure will allow.
NOTE 1—It is not possible to specify a minimum age when concrete is strong enough to withstand damage during removal, because the strength at any age depends on the curing history and strength grade of the concrete.
When preparing strength test specimens from samples of hardened concrete, samples that show defects or samples that have been damaged in the process of removal shall not be used.
SI units are shown in brackets.