ASTM A – Designation: A /A M – 02a Standard Speci?cation for Steel Sheet, Aluminum-. Find the most up-to-date version of ASTM A at Engineering ASTM A/AM: Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process.
|Published (Last):||24 January 2006|
|PDF File Size:||14.5 Mb|
|ePub File Size:||18.33 Mb|
|Price:||Free* [*Free Regsitration Required]|
The purchaser may negotiate with the supplier if a speci? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
ASTM A Aluminum-Coated Steel, Type I, Drawing Quality
Please contact us at webmaster matweb. These factors 3 include: The yield strength tends to increase and some of the formability values tend to decrease as the sheet thickness decreases. Property Data This page displays only the text of a material data sheet. B Weight [mass] to thickness conversions are reliable to only two signi?
Values in inch-pound and SI units are not necessarily equivalent. It is available as a coating on each of the designations of steel sheet listed in 4. Continuing dialogue between users and producers will have to be maintained to assist in the transition to the new designation system.
J Shall contain silicon 1. The following, as required, shall be used to adequately describe the product required.
Login to see your most recently viewed materials here. For all designations the coating bend test inside diameter shall be equal to twice the thickness of the specimen.
The purchaser shall specify the appropriate table of thickness tolerances in Speci? A superscript epsilon e indicates an editorial change since the last revision or reapproval.
This is not considered to be a fault of the steel but is rather a function of the induced cold-work. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
A greater number of digits are shown in Table X2. Link to Active This link will always route to the current Active version of the standard.
In such cases, the applicable limit for vanadium and columbium shall be 0. There are many interrelated factors that affect the ability of a steel to cold form over a given radius under shop conditions.
A4463 Shall contain silicon 1. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
D If a higher tensile strength is required, the user should consult the producer. This standard x463 subject to revision at any time by the responsible technical committee and must be reviewed every? Historical Version s – view astk versions of standard. All other values in Table X2. These notes and footnotes excluding those in tables and figures shall not be considered as requirements of the standard.
A One ounce of Type 1 aluminum coating per square foot of surface corresponds to an average coating thickness of 0. C these ranges are to be expected.
This standard has been approved for use by agencies of the Department of Defense. B No minimum means aetm there are no established minimum requirements for triple- and single-spot tests, but aluminum coating shall be present.
Originally published as A — 62 T. Values outside of these ranges are to be expected. Or if you don’t have an account with us yet, then click here to register. The former designations also did not re? Coating weight and bend tests shall be made to conform to the requirements specified.
ASTM A463 Grade FSS-439
Aluminum-coated type 1 steel, coils or cut sheet Coated with aluminum-silicon alloy by hot dip process Used for combustion chambers, exhaust systems, heat a43 and reflectors, ovens, grills, and appliances Vendors: Structural steel and high strength low alloy steel shall conform to the mechanical property requirements.
B These typical mechanical properties apply to the full range of steel sheet thicknesses. Values in inch-pound and SI units are not necessarily equivalent. These steel characteristics are important to users concerned with the weldability and formability of the coated steel products. Aluminum-coated type 1 steel, coils or cut sheet Coated with aluminum-silicon alloy by hot dip process Used for combustion chambers, exhaust systems, heat exchangers and reflectors, ovens, grills, and appliances.